- May 12, 2022
-
-
Duoming Zhou authored
commit 47f070a6 upstream. There are deadlocks caused by del_timer_sync(&priv->hang_timer) and del_timer_sync(&priv->rr_timer) in grcan_close(), one of the deadlocks are shown below: (Thread 1) | (Thread 2) | grcan_reset_timer() grcan_close() | mod_timer() spin_lock_irqsave() //(1) | (wait a time) ... | grcan_initiate_running_reset() del_timer_sync() | spin_lock_irqsave() //(2) (wait timer to stop) | ... We hold priv->lock in position (1) of thread 1 and use del_timer_sync() to wait timer to stop, but timer handler also need priv->lock in position (2) of thread 2. As a result, grcan_close() will block forever. This patch extracts del_timer_sync() from the protection of spin_lock_irqsave(), which could let timer handler to obtain the needed lock. Link: https://lore.kernel.org/all/20220425042400.66517-1-duoming@zju.edu.cn Fixes: 6cec9b07 ("can: grcan: Add device driver for GRCAN and GRHCAN cores") Cc: stable@vger.kernel.org Signed-off-by:
Duoming Zhou <duoming@zju.edu.cn> Reviewed-by:
Andreas Larsson <andreas@gaisler.com> Signed-off-by:
Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Mark Brown authored
commit b4f5c6b2 upstream. The WM8958 DSP controls all return 0 on successful write, not a boolean value indicating if the write changed the value of the control. Fix this by returning 1 after a change, there is already a check at the start of each put() that skips the function in the case that there is no change. Signed-off-by:
Mark Brown <broonie@kernel.org> Acked-by:
Charles Keepax <ckeepax@opensource.cirrus.com> Link: https://lore.kernel.org/r/20220416125408.197440-1-broonie@kernel.org Cc: stable@vger.kernel.org Signed-off-by:
-
Thomas Pfaff authored
commit 8707898e upstream. A kernel hang can be observed when running setserial in a loop on a kernel with force threaded interrupts. The sequence of events is: setserial open("/dev/ttyXXX") request_irq() do_stuff() -> serial interrupt -> wake(irq_thread) desc->threads_active++; close() free_irq() kthread_stop(irq_thread) synchronize_irq() <- hangs because desc->threads_active != 0 The thread is created in request_irq() and woken up, but does not get on a CPU to reach the actual thread function, which would handle the pending wake-up. kthread_stop() sets the should stop condition which makes the thread immediately exit, which in turn leaves the stale threads_active count around. This problem was introduced with commit 519cc865, which addressed a interrupt sharing issue in the PCIe code. Before that commit free_irq() invoked synchronize_irq(), which waits for the hard interrupt handler and also for associated threads to complete. To address the PCIe issue synchronize_irq() was replaced with __synchronize_hardirq(), which only waits for the hard interrupt handler to complete, but not for threaded handlers. This was done under the assumption, that the interrupt thread already reached the thread function and waits for a wake-up, which is guaranteed to be handled before acting on the stop condition. The problematic case, that the thread would not reach the thread function, was obviously overlooked. Make sure that the interrupt thread is really started and reaches thread_fn() before returning from __setup_irq(). This utilizes the existing wait queue in the interrupt descriptor. The wait queue is unused for non-shared interrupts. For shared interrupts the usage might cause a spurious wake-up of a waiter in synchronize_irq() or the completion of a threaded handler might cause a spurious wake-up of the waiter for the ready flag. Both are harmless and have no functional impact. [ tglx: Amended changelog ] Fixes: 519cc865 ("genirq: Synchronize only with single thread on free_irq()") Signed-off-by:
Thomas Pfaff <tpfaff@pcs.com> Signed-off-by:
Thomas Gleixner <tglx@linutronix.de> Reviewed-by:
Marc Zyngier <maz@kernel.org> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/552fe7b4-9224-b183-bb87-a8f36d335690@pcs.com Signed-off-by:
-
Niels Dossche authored
commit a7ecbe92 upstream. card->local_node and card->bm_retries are both always accessed under card->lock. fw_core_handle_bus_reset has a check whose condition depends on card->local_node and whose body writes to card->bm_retries. Both of these accesses are not under card->lock. Move the lock acquiring of card->lock to before this check such that these accesses do happen when card->lock is held. fw_destroy_nodes is called inside the check. Since fw_destroy_nodes already acquires card->lock inside its function body, move this out to the callsites of fw_destroy_nodes. Also add a comment to indicate which locking is necessary when calling fw_destroy_nodes. Cc: <stable@vger.kernel.org> Signed-off-by:
Niels Dossche <dossche.niels@gmail.com> Signed-off-by:
Takashi Sakamoto <o-takashi@sakamocchi.jp> Link: https://lore.kernel.org/r/20220409041243.603210-4-o-takashi@sakamocchi.jp Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Jakob Koschel authored
commit 94239738 upstream. When list_for_each_entry() completes the iteration over the whole list without breaking the loop, the iterator value will be a bogus pointer computed based on the head element. While it is safe to use the pointer to determine if it was computed based on the head element, either with list_entry_is_head() or &pos->member == head, using the iterator variable after the loop should be avoided. In preparation to limit the scope of a list iterator to the list traversal loop, use a dedicated pointer to point to the found element [1]. Link: https://lore.kernel.org/all/CAHk-=wgRr_D8CB-D9Kg-c=EHreAsk5SqXPwr9Y7k9sA6cWXJ6w@mail.gmail.com/ [1] Cc: <stable@vger.kernel.org> Signed-off-by:
Jakob Koschel <jakobkoschel@gmail.com> Signed-off-by:
-
Chengfeng Ye authored
commit b7c81f80 upstream. &e->event and e point to the same address, and &e->event could be freed in queue_event. So there is a potential uaf issue if we dereference e after calling queue_event(). Fix this by adding a temporary variable to maintain e->client in advance, this can avoid the potential uaf issue. Cc: <stable@vger.kernel.org> Signed-off-by:
Chengfeng Ye <cyeaa@connect.ust.hk> Signed-off-by:
-
Trond Myklebust authored
commit a3d0562d upstream. This reverts commit 7073ea87. We must not try to connect the socket while the transport is under construction, because the mechanisms to safely tear it down are not in place. As the code stands, we end up leaking the sockets on a connection error. Reported-by:
wanghai (M) <wanghai38@huawei.com> Cc: stable@vger.kernel.org Signed-off-by:
Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by:
-
Andrei Lalaev authored
commit e75f88ef upstream. Gpiolib interprets the elements of "gpio-reserved-ranges" as "start,size" because it clears "size" bits starting from the "start" bit in the according bitmap. So it has to use "greater" instead of "greater or equal" when performs bounds check to make sure that GPIOs are in the available range. Previous implementation skipped ranges that include the last GPIO in the range. I wrote the mail to the maintainers (https://lore.kernel.org/linux-gpio/20220412115554.159435-1-andrei.lalaev@emlid.com/T/#u ) of the questioned DTSes (because I couldn't understand how the maintainers interpreted this property), but I haven't received a response. Since the questioned DTSes use "gpio-reserved-ranges = <0 4>" (i.e., the beginning of the range), this patch doesn't affect these DTSes at all. TBH this patch doesn't break any existing DTSes because none of them reserve gpios at the end of range. Fixes: 726cb3ba ("gpiolib: Support 'gpio-reserved-ranges' property") Signed-off-by:
Andrei Lalaev <andrei.lalaev@emlid.com> Reviewed-by:
Andy Shevchenko <andy.shevchenko@gmail.com> Reviewed-by:
Linus Walleij <linus.walleij@linaro.org> Cc: stable@vger.kernel.org Signed-off-by:
Bartosz Golaszewski <brgl@bgdev.pl> Signed-off-by:
-
Takashi Sakamoto authored
commit eb9d84b0 upstream. ALSA fireworks driver has a bug in its initial state to return count shorter than expected by 4 bytes to userspace applications when handling response frame for Echo Audio Fireworks transaction. It's due to missing addition of the size for the type of event in ALSA firewire stack. Fixes: 555e8a8f ("ALSA: fireworks: Add command/response functionality into hwdep interface") Cc: <stable@vger.kernel.org> Signed-off-by:
-
Helge Deller authored
commit 5b89966b upstream. The Linux tool "lscpu" shows the double amount of CPUs if we have "model" and "model name" in two different lines in /proc/cpuinfo. This change combines the model and the model name into one line. Signed-off-by:
Helge Deller <deller@gmx.de> Cc: stable@vger.kernel.org Signed-off-by:
-
Maciej W. Rozycki authored
commit f0a6c68f upstream. Fix the discrepancy between the two places we check for the CP0 counter erratum in along with the incorrect comparison of the R4400 revision number against 0x30 which matches none and consistently consider all R4000 and R4400 processors affected, as documented in processor errata publications[1][2][3], following the mapping between CP0 PRId register values and processor models: PRId | Processor Model ---------+-------------------- 00000422 | R4000 Revision 2.2 00000430 | R4000 Revision 3.0 00000440 | R4400 Revision 1.0 00000450 | R4400 Revision 2.0 00000460 | R4400 Revision 3.0 No other revision of either processor has ever been spotted. Contrary to what has been stated in commit ce202cbb ("[MIPS] Assume R4000/R4400 newer than 3.0 don't have the mfc0 count bug") marking the CP0 counter as buggy does not preclude it from being used as either a clock event or a clock source device. It just cannot be used as both at a time, because in that case clock event interrupts will be occasionally lost, and the use as a clock event device takes precedence. Compare against 0x4ff in `can_use_mips_counter' so that a single machine instruction is produced. References: [1] "MIPS R4000PC/SC Errata, Processor Revision 2.2 and 3.0", MIPS Technologies Inc., May 10, 1994, Erratum 53, p.13 [2] "MIPS R4400PC/SC Errata, Processor Revision 1.0", MIPS Technologies Inc., February 9, 1994, Erratum 21, p.4 [3] "MIPS R4400PC/SC Errata, Processor Revision 2.0 & 3.0", MIPS Technologies Inc., January 24, 1995, Erratum 14, p.3 Signed-off-by:
Maciej W. Rozycki <macro@orcam.me.uk> Fixes: ce202cbb ("[MIPS] Assume R4000/R4400 newer than 3.0 don't have the mfc0 count bug") Cc: stable@vger.kernel.org # v2.6.24+ Reviewed-by:
Philippe Mathieu-Daudé <f4bug@amsat.org> Signed-off-by:
Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by:
-
Daniel Vetter authored
commit 4b848f20 upstream. There's two references floating around here (for the object reference, not the handle_count reference, that's a different thing): - The temporary reference held by vgem_gem_create, acquired by creating the object and released by calling drm_gem_object_put_unlocked. - The reference held by the object handle, created by drm_gem_handle_create. This one generally outlives the function, except if a 2nd thread races with a GEM_CLOSE ioctl call. So usually everything is correct, except in that race case, where the access to gem_object->size could be looking at freed data already. Which again isn't a real problem (userspace shot its feet off already with the race, we could return garbage), but maybe someone can exploit this as an information leak. Cc: Dan Carpenter <dan.carpenter@oracle.com> Cc: Hillf Danton <hdanton@sina.com> Reported-by:
<syzbot+0dc4444774d419e916c8@syzkaller.appspotmail.com> Cc: stable@vger.kernel.org Cc: Emil Velikov <emil.velikov@collabora.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Sean Paul <seanpaul@chromium.org> Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Eric Anholt <eric@anholt.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Rob Clark <robdclark@chromium.org> Reviewed-by:
Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by:
Daniel Vetter <daniel.vetter@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200202132133.1891846-1-daniel.vetter@ffwll.ch [OP: backport to 4.19: adjusted DRM_DEBUG() -> DRM_DEBUG_DRIVER()] Signed-off-by:
Ovidiu Panait <ovidiu.panait@windriver.com> Signed-off-by:
-
Daniel Starke authored
commit ff9166c6 upstream. n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010. See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516 The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to the newer 27.010 here. Chapter 5.4.4.2 states that any received unnumbered acknowledgment (UA) with its poll/final (PF) bit set to 0 shall be discarded. Currently, all UA frame are handled in the same way regardless of the PF bit. This does not comply with the standard. Remove the UA case in gsm_queue() to process only UA frames with PF bit set to 1 to abide the standard. Fixes: e1eaea46 ("tty: n_gsm line discipline") Cc: stable@vger.kernel.org Signed-off-by:
Daniel Starke <daniel.starke@siemens.com> Link: https://lore.kernel.org/r/20220414094225.4527-20-daniel.starke@siemens.com Signed-off-by:
-
Daniel Starke authored
commit 398867f5 upstream. n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010. See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516 The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to the newer 27.010 here. Chapter 5.4.6.1 states that each command frame shall be made up from type, length and value. Looking for example in chapter 5.4.6.3.5 at the description for the encoding of a flow control on command it becomes obvious, that the type and length field is always present whereas the value may be zero bytes long. The current implementation omits the length field if the value is not present. This is wrong. Correct this by always sending the length in gsm_control_transmit(). So far only the modem status command (MSC) has included a value and encoded its length directly. Therefore, also change gsmtty_modem_update(). Fixes: e1eaea46 ("tty: n_gsm line discipline") Cc: stable@vger.kernel.org Signed-off-by:
-
Daniel Starke authored
commit d0bcdffc upstream. n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010. See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516 The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to the newer 27.010 here. Chapter 5.7.3 states that the valid range for the maximum number of retransmissions (N2) is from 0 to 255 (both including). gsm_config() fails to limit this range correctly. Furthermore, gsm_control_retransmit() handles this number incorrectly by performing N2 - 1 retransmission attempts. Setting N2 to zero results in more than 255 retransmission attempts. Fix the range check in gsm_config() and the value handling in gsm_control_send() and gsm_control_retransmit() to comply with 3GPP 27.010. Fixes: e1eaea46 ("tty: n_gsm line discipline") Cc: stable@vger.kernel.org Signed-off-by:
-
Daniel Starke authored
commit 17eac652 upstream. In gsm_cleanup_mux() the muxer is closed down and all queues are removed. However, removing the queues is done without explicit control of the underlying buffers. Flush those before freeing up our queues to ensure that all outgoing queues are cleared consistently. Otherwise, a new mux connection establishment attempt may time out while the underlying tty is still busy sending out the remaining data from the previous connection. Fixes: e1eaea46 ("tty: n_gsm line discipline") Cc: stable@vger.kernel.org Signed-off-by:
-
Daniel Starke authored
commit 535bf600 upstream. n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010. See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516 The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to the newer 27.010 here. Chapter 5.7.2 states that the maximum frame size (N1) refers to the length of the information field (i.e. user payload). However, 'txframe' stores the whole frame including frame header, checksum and start/end flags. We also need to consider the byte stuffing overhead. Define constant for the protocol overhead and adjust the 'txframe' size calculation accordingly to reserve enough space for a complete mux frame including byte stuffing for advanced option mode. Note that no byte stuffing is applied to the start and end flag. Also use MAX_MTU instead of MAX_MRU as this buffer is used for data transmission. Fixes: e1eaea46 ("tty: n_gsm line discipline") Cc: stable@vger.kernel.org Signed-off-by:
-
Florian Westphal authored
commit 743b83f1 upstream. Check if the incoming interface is available and NFT_BREAK in case neither skb->sk nor input device are set. Because nf_sk_lookup_slow*() assume packet headers are in the 'in' direction, use in postrouting is not going to yield a meaningful result. Same is true for the forward chain, so restrict the use to prerouting, input and output. Use in output work if a socket is already attached to the skb. Fixes: 554ced0a ("netfilter: nf_tables: add support for native socket matching") Reported-and-tested-by:
Topi Miettinen <toiwoton@gmail.com> Signed-off-by:
Florian Westphal <fw@strlen.de> Signed-off-by:
Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by:
-
Daniel Starke authored
commit a24b4b2f upstream. The gsm_mux field 'malformed' represents the number of malformed frames received. However, gsm1_receive() also increases this counter for any out of frame byte. Fix this by ignoring out of frame data for the malformed counter. Fixes: e1eaea46 ("tty: n_gsm line discipline") Cc: stable@vger.kernel.org Signed-off-by:
-
Daniel Starke authored
commit 06d5afd4 upstream. n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010. See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516 The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to the newer 27.010 here. Chapter 5.5.2 describes that the signal octet in convergence layer type 2 can be either one or two bytes. The length is encoded in the EA bit. This is set 1 for the last byte in the sequence. gsmtty_modem_update() handles this correctly but gsm_dlci_data_output() fails to set EA to 1. There is no case in which we encode two signal octets as there is no case in which we send out a break signal. Therefore, always set the EA bit to 1 for the signal octet to fix this. Fixes: e1eaea46 ("tty: n_gsm line discipline") Cc: stable@vger.kernel.org Signed-off-by:
-
Borislav Petkov authored
commit f9e14dbb upstream. When resuming from system sleep state, restore_processor_state() restores the boot CPU MSRs. These MSRs could be emulated by microcode. If microcode is not loaded yet, writing to emulated MSRs leads to unchecked MSR access error: ... PM: Calling lapic_suspend+0x0/0x210 unchecked MSR access error: WRMSR to 0x10f (tried to write 0x0...0) at rIP: ... (native_write_msr) Call Trace: <TASK> ? restore_processor_state x86_acpi_suspend_lowlevel acpi_suspend_enter suspend_devices_and_enter pm_suspend.cold state_store kobj_attr_store sysfs_kf_write kernfs_fop_write_iter new_sync_write vfs_write ksys_write __x64_sys_write do_syscall_64 entry_SYSCALL_64_after_hwframe RIP: 0033:0x7fda13c260a7 To ensure microcode emulated MSRs are available for restoration, load the microcode on the boot CPU before restoring these MSRs. [ Pawan: write commit message and productize it. ] Fixes: e2a1256b ("x86/speculation: Restore speculation related MSRs during S3 resume") Reported-by:
Kyle D. Pelton <kyle.d.pelton@intel.com> Signed-off-by:
Borislav Petkov <bp@suse.de> Signed-off-by:
Pawan Gupta <pawan.kumar.gupta@linux.intel.com> Tested-by:
-
Duoming Zhou authored
[ Upstream commit bc6de287 ] There is a deadlock in rr_close(), which is shown below: (Thread 1) | (Thread 2) | rr_open() rr_close() | add_timer() spin_lock_irqsave() //(1) | (wait a time) ... | rr_timer() del_timer_sync() | spin_lock_irqsave() //(2) (wait timer to stop) | ... We hold rrpriv->lock in position (1) of thread 1 and use del_timer_sync() to wait timer to stop, but timer handler also need rrpriv->lock in position (2) of thread 2. As a result, rr_close() will block forever. This patch extracts del_timer_sync() from the protection of spin_lock_irqsave(), which could let timer handler to obtain the needed lock. Signed-off-by:
Paolo Abeni <pabeni@redhat.com> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Ronnie Sahlberg authored
[ Upstream commit f5d0f921 ] because the copychunk_write might cover a region of the file that has not yet been sent to the server and thus fail. A simple way to reproduce this is: truncate -s 0 /mnt/testfile; strace -f -o x -ttT xfs_io -i -f -c 'pwrite 0k 128k' -c 'fcollapse 16k 24k' /mnt/testfile the issue is that the 'pwrite 0k 128k' becomes rearranged on the wire with the 'fcollapse 16k 24k' due to write-back caching. fcollapse is implemented in cifs.ko as a SMB2 IOCTL(COPYCHUNK_WRITE) call and it will fail serverside since the file is still 0b in size serverside until the writes have been destaged. To avoid this we must ensure that we destage any unwritten data to the server before calling COPYCHUNK_WRITE. Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1997373 Reported-by:
Xiaoli Feng <xifeng@redhat.com> Signed-off-by:
Ronnie Sahlberg <lsahlber@redhat.com> Signed-off-by:
Steve French <stfrench@microsoft.com> Signed-off-by:
-
Mikulas Patocka authored
[ Upstream commit a6823e4e ] The first "if" condition in __memcpy_flushcache is supposed to align the "dest" variable to 8 bytes and copy data up to this alignment. However, this condition may misbehave if "size" is greater than 4GiB. The statement min_t(unsigned, size, ALIGN(dest, 8) - dest); casts both arguments to unsigned int and selects the smaller one. However, the cast truncates high bits in "size" and it results in misbehavior. For example: suppose that size == 0x100000001, dest == 0x200000002 min_t(unsigned, size, ALIGN(dest, 8) - dest) == min_t(0x1, 0xe) == 0x1; ... dest += 0x1; so we copy just one byte "and" dest remains unaligned. This patch fixes the bug by replacing unsigned with size_t. Signed-off-by:
Mikulas Patocka <mpatocka@redhat.com> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Peilin Ye authored
[ Upstream commit f40c064e ] Do not update tunnel->tun_hlen in data plane code. Use a local variable instead, just like "tunnel_hlen" in net/ipv4/ip_gre.c:gre_fb_xmit(). Co-developed-by:
Cong Wang <cong.wang@bytedance.com> Signed-off-by:
Peilin Ye <peilin.ye@bytedance.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Zheyu Ma authored
[ Upstream commit 92ccbf17 ] When the driver fails during probing, the driver should disable the regulator, not just handle it in wm8731_hw_init(). The following log reveals it: [ 17.812483] WARNING: CPU: 1 PID: 364 at drivers/regulator/core.c:2257 _regulator_put+0x3ec/0x4e0 [ 17.815958] RIP: 0010:_regulator_put+0x3ec/0x4e0 [ 17.824467] Call Trace: [ 17.824774] <TASK> [ 17.825040] regulator_bulk_free+0x82/0xe0 [ 17.825514] devres_release_group+0x319/0x3d0 [ 17.825882] i2c_device_probe+0x766/0x940 [ 17.829198] i2c_register_driver+0xb5/0x130 Signed-off-by:
Zheyu Ma <zheyuma97@gmail.com> Link: https://lore.kernel.org/r/20220405121038.4094051-1-zheyuma97@gmail.com Signed-off-by:
-
Manish Chopra authored
[ Upstream commit af68656d ] While handling PCI errors (AER flow) driver tries to disable NAPI [napi_disable()] after NAPI is deleted [__netif_napi_del()] which causes unexpected system hang/crash. System message log shows the following: ======================================= [ 3222.537510] EEH: Detected PCI bus error on PHB#384-PE#800000 [ 3222.537511] EEH: This PCI device has failed 2 times in the last hour and will be permanently disabled after 5 failures. [ 3222.537512] EEH: Notify device drivers to shutdown [ 3222.537513] EEH: Beginning: 'error_detected(IO frozen)' [ 3222.537514] EEH: PE#800000 (PCI 0384:80:00.0): Invoking bnx2x->error_detected(IO frozen) [ 3222.537516] bnx2x: [bnx2x_io_error_detected:14236(eth14)]IO error detected [ 3222.537650] EEH: PE#800000 (PCI 0384:80:00.0): bnx2x driver reports: 'need reset' [ 3222.537651] EEH: PE#800000 (PCI 0384:80:00.1): Invoking bnx2x->error_detected(IO frozen) [ 3222.537651] bnx2x: [bnx2x_io_error_detected:14236(eth13)]IO error detected [ 3222.537729] EEH: PE#800000 (PCI 0384:80:00.1): bnx2x driver reports: 'need reset' [ 3222.537729] EEH: Finished:'error_detected(IO frozen)' with aggregate recovery state:'need reset' [ 3222.537890] EEH: Collect temporary log [ 3222.583481] EEH: of node=0384:80:00.0 [ 3222.583519] EEH: PCI device/vendor: 168e14e4 [ 3222.583557] EEH: PCI cmd/status register: 00100140 [ 3222.583557] EEH: PCI-E capabilities and status follow: [ 3222.583744] EEH: PCI-E 00: 00020010 012c8da2 00095d5e 00455c82 [ 3222.583892] EEH: PCI-E 10: 10820000 00000000 00000000 00000000 [ 3222.583893] EEH: PCI-E 20: 00000000 [ 3222.583893] EEH: PCI-E AER capability register set follows: [ 3222.584079] EEH: PCI-E AER 00: 13c10001 00000000 00000000 00062030 [ 3222.584230] EEH: PCI-E AER 10: 00002000 000031c0 000001e0 00000000 [ 3222.584378] EEH: PCI-E AER 20: 00000000 00000000 00000000 00000000 [ 3222.584416] EEH: PCI-E AER 30: 00000000 00000000 [ 3222.584416] EEH: of node=0384:80:00.1 [ 3222.584454] EEH: PCI device/vendor: 168e14e4 [ 3222.584491] EEH: PCI cmd/status register: 00100140 [ 3222.584492] EEH: PCI-E capabilities and status follow: [ 3222.584677] EEH: PCI-E 00: 00020010 012c8da2 00095d5e 00455c82 [ 3222.584825] EEH: PCI-E 10: 10820000 00000000 00000000 00000000 [ 3222.584826] EEH: PCI-E 20: 00000000 [ 3222.584826] EEH: PCI-E AER capability register set follows: [ 3222.585011] EEH: PCI-E AER 00: 13c10001 00000000 00000000 00062030 [ 3222.585160] EEH: PCI-E AER 10: 00002000 000031c0 000001e0 00000000 [ 3222.585309] EEH: PCI-E AER 20: 00000000 00000000 00000000 00000000 [ 3222.585347] EEH: PCI-E AER 30: 00000000 00000000 [ 3222.586872] RTAS: event: 5, Type: Platform Error (224), Severity: 2 [ 3222.586873] EEH: Reset without hotplug activity [ 3224.762767] EEH: Beginning: 'slot_reset' [ 3224.762770] EEH: PE#800000 (PCI 0384:80:00.0): Invoking bnx2x->slot_reset() [ 3224.762771] bnx2x: [bnx2x_io_slot_reset:14271(eth14)]IO slot reset initializing... [ 3224.762887] bnx2x 0384:80:00.0: enabling device (0140 -> 0142) [ 3224.768157] bnx2x: [bnx2x_io_slot_reset:14287(eth14)]IO slot reset --> driver unload Uninterruptible tasks ===================== crash> ps | grep UN 213 2 11 c000000004c89e00 UN 0.0 0 0 [eehd] 215 2 0 c000000004c80000 UN 0.0 0 0 [kworker/0:2] 2196 1 28 c000000004504f00 UN 0.1 15936 11136 wickedd 4287 1 9 c00000020d076800 UN 0.0 4032 3008 agetty 4289 1 20 c00000020d056680 UN 0.0 7232 3840 agetty 32423 2 26 c00000020038c580 UN 0.0 0 0 [kworker/26:3] 32871 4241 27 c0000002609ddd00 UN 0.1 18624 11648 sshd 32920 10130 16 c00000027284a100 UN 0.1 48512 12608 sendmail 33092 32987 0 c000000205218b00 UN 0.1 48512 12608 sendmail 33154 4567 16 c000000260e51780 UN 0.1 48832 12864 pickup 33209 4241 36 c000000270cb6500 UN 0.1 18624 11712 sshd 33473 33283 0 c000000205211480 UN 0.1 48512 12672 sendmail 33531 4241 37 c00000023c902780 UN 0.1 18624 11648 sshd EEH handler hung while bnx2x sleeping and holding RTNL lock =========================================================== crash> bt 213 PID: 213 TASK: c000000004c89e00 CPU: 11 COMMAND: "eehd" #0 [c000000004d477e0] __schedule at c000000000c70808 #1 [c000000004d478b0] schedule at c000000000c70ee0 #2 [c000000004d478e0] schedule_timeout at c000000000c76dec #3 [c000000004d479c0] msleep at c0000000002120cc #4 [c000000004d479f0] napi_disable at c000000000a06448 ^^^^^^^^^^^^^^^^ #5 [c000000004d47a30] bnx2x_netif_stop at c0080000018dba94 [bnx2x] #6 [c000000004d47a60] bnx2x_io_slot_reset at c0080000018a551c [bnx2x] #7 [c000000004d47b20] eeh_report_reset at c00000000004c9bc #8 [c000000004d47b90] eeh_pe_report at c00000000004d1a8 #9 [c000000004d47c40] eeh_handle_normal_event at c00000000004da64 And the sleeping source code ============================ crash> dis -ls c000000000a06448 FILE: ../net/core/dev.c LINE: 6702 6697 { 6698 might_sleep(); 6699 set_bit(NAPI_STATE_DISABLE, &n->state); 6700 6701 while (test_and_set_bit(NAPI_STATE_SCHED, &n->state)) * 6702 msleep(1); 6703 while (test_and_set_bit(NAPI_STATE_NPSVC, &n->state)) 6704 msleep(1); 6705 6706 hrtimer_cancel(&n->timer); 6707 6708 clear_bit(NAPI_STATE_DISABLE, &n->state); 6709 } EEH calls into bnx2x twice based on the system log above, first through bnx2x_io_error_detected() and then bnx2x_io_slot_reset(), and executes the following call chains: bnx2x_io_error_detected() +-> bnx2x_eeh_nic_unload() +-> bnx2x_del_all_napi() +-> __netif_napi_del() bnx2x_io_slot_reset() +-> bnx2x_netif_stop() +-> bnx2x_napi_disable() +->napi_disable() Fix this by correcting the sequence of NAPI APIs usage, that is delete the NAPI after disabling it. Fixes: 7fa6f340 ("bnx2x: AER revised") Reported-by:
David Christensen <drc@linux.vnet.ibm.com> Tested-by:
Manish Chopra <manishc@marvell.com> Signed-off-by:
Ariel Elior <aelior@marvell.com> Link: https://lore.kernel.org/r/20220426153913.6966-1-manishc@marvell.com Signed-off-by:
Jakub Kicinski <kuba@kernel.org> Signed-off-by:
-
Jonathan Lemon authored
[ Upstream commit acac0541 ] The hardware checksum offloading requires use of a transmit status block inserted before the outgoing frame data, this was updated in '9a9ba2a4 ("net: bcmgenet: always enable status blocks")' However, skb_tx_timestamp() assumes that it is passed a raw frame and PTP parsing chokes on this status block. Fix this by calling __skb_pull(), which hides the TSB before calling skb_tx_timestamp(), so an outgoing PTP packet is parsed correctly. As the data in the skb has already been set up for DMA, and the dma_unmap_* calls use a separately stored address, there is no no effective change in the data transmission. Signed-off-by:
Jonathan Lemon <jonathan.lemon@gmail.com> Acked-by:
Florian Fainelli <f.fainelli@gmail.com> Link: https://lore.kernel.org/r/20220424165307.591145-1-jonathan.lemon@gmail.com Fixes: d03825fb ("net: bcmgenet: add skb_tx_timestamp call") Signed-off-by:
-
Yang Yingliang authored
[ Upstream commit f58ca215 ] It will cause null-ptr-deref if platform_get_resource() returns NULL, we need check the return value. Fixes: 7a6fca87 ("clk: sunxi: Add driver for A80 MMC config clocks/resets") Signed-off-by:
Yang Yingliang <yangyingliang@huawei.com> Reviewed-by:
Samuel Holland <samuel@sholland.org> Signed-off-by:
Jernej Skrabec <jernej.skrabec@gmail.com> Link: https://lore.kernel.org/r/20220421134308.2885094-1-yangyingliang@huawei.com Signed-off-by:
-
Christophe JAILLET authored
[ Upstream commit fff8c103 ] This code is really spurious. It always returns an ERR_PTR, even when err is known to be 0 and calls put_device() after a successful device_register() call. It is likely that the return statement in the normal path is missing. Add 'return rdev;' to fix it. Fixes: d787dcdb ("bus: sunxi-rsb: Add driver for Allwinner Reduced Serial Bus") Signed-off-by:
Christophe JAILLET <christophe.jaillet@wanadoo.fr> Reviewed-by:
-
Eric Dumazet authored
[ Upstream commit 4bfe744f ] I had this bug sitting for too long in my pile, it is time to fix it. Thanks to Doug Porter for reminding me of it! We had various attempts in the past, including commit 0cbe6a8f ("tcp: remove SOCK_QUEUE_SHRUNK"), but the issue is that TCP stack currently only generates EPOLLOUT from input path, when tp->snd_una has advanced and skb(s) cleaned from rtx queue. If a flow has a big RTT, and/or receives SACKs, it is possible that the notsent part (tp->write_seq - tp->snd_nxt) reaches 0 and no more data can be sent until tp->snd_una finally advances. What is needed is to also check if POLLOUT needs to be generated whenever tp->snd_nxt is advanced, from output path. This bug triggers more often after an idle period, as we do not receive ACK for at least one RTT. tcp_notsent_lowat could be a fraction of what CWND and pacing rate would allow to send during this RTT. In a followup patch, I will remove the bogus call to tcp_chrono_stop(sk, TCP_CHRONO_SNDBUF_LIMITED) from tcp_check_space(). Fact that we have decided to generate an EPOLLOUT does not mean the application has immediately refilled the transmit queue. This optimistic call might have been the reason the bug seemed not too serious. Tested: 200 ms rtt, 1% packet loss, 32 MB tcp_rmem[2] and tcp_wmem[2] $ echo 500000 >/proc/sys/net/ipv4/tcp_notsent_lowat $ cat bench_rr.sh SUM=0 for i in {1..10} do V=`netperf -H remote_host -l30 -t TCP_RR -- -r 10000000,10000 -o LOCAL_BYTES_SENT | egrep -v "MIGRATED|Bytes"` echo $V SUM=$(($SUM + $V)) done echo SUM=$SUM Before patch: $ bench_rr.sh 130000000 80000000 140000000 140000000 140000000 140000000 130000000 40000000 90000000 110000000 SUM=1140000000 After patch: $ bench_rr.sh 430000000 590000000 530000000 450000000 450000000 350000000 450000000 490000000 480000000 460000000 SUM=4680000000 # This is 410 % of the value before patch. Fixes: c9bee3b7 ("tcp: TCP_NOTSENT_LOWAT socket option") Signed-off-by:
Eric Dumazet <edumazet@google.com> Reported-by:
Doug Porter <dsp@fb.com> Cc: Soheil Hassas Yeganeh <soheil@google.com> Cc: Neal Cardwell <ncardwell@google.com> Acked-by:
Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by:
-
Peilin Ye authored
[ Upstream commit ff827beb ] For GRE and GRETAP devices, currently o_seqno starts from 1 in native mode. According to RFC 2890 2.2., "The first datagram is sent with a sequence number of 0." Fix it. It is worth mentioning that o_seqno already starts from 0 in collect_md mode, see gre_fb_xmit(), where tunnel->o_seqno is passed to gre_build_header() before getting incremented. Fixes: 1da177e4 ("Linux-2.6.12-rc2") Signed-off-by:
William Tu <u9012063@gmail.com> Signed-off-by:
-
Jian Shen authored
[ Upstream commit 7d413735 ] Add validity check for message data length in function hclge_send_mbx_msg(), avoid unexpected overflow. Fixes: dde1a86e ("net: hns3: Add mailbox support to PF driver") Signed-off-by:
Jian Shen <shenjian15@huawei.com> Signed-off-by:
Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by:
-
Lv Ruyi authored
[ Upstream commit 0c9843a7 ] The irq_of_parse_and_map() function returns 0 on failure, and does not return an negative value. Fixes: cefc03e5 ("pinctrl: Add Pistachio SoC pin control driver") Reported-by:
Zeal Robot <zealci@zte.com.cn> Signed-off-by:
Lv Ruyi <lv.ruyi@zte.com.cn> Link: https://lore.kernel.org/r/20220424031430.3170759-1-lv.ruyi@zte.com.cn Signed-off-by:
-
Max Krummenacher authored
[ Upstream commit 45974e42 ] The correct spelling for the property is gpios. Otherwise, the regulator will neither reserve nor control any GPIOs. Thus, any SD/MMC card which can use UHS-I modes will fail. Fixes: c2e4987e ("ARM: dts: imx6ull: add Toradex Colibri iMX6ULL support") Signed-off-by:
Max Krummenacher <max.krummenacher@toradex.com> Signed-off-by:
Denys Drozdov <denys.drozdov@toradex.com> Signed-off-by:
Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by:
Shawn Guo <shawnguo@kernel.org> Signed-off-by:
-
Xin Long authored
[ Upstream commit 165e3e17 ] A null pointer reference issue can be triggered when the response of a stream reconf request arrives after the timer is triggered, such as: send Incoming SSN Reset Request ---> CPU0: reconf timer is triggered, go to the handler code before hold sk lock <--- reply with Outgoing SSN Reset Request CPU1: process Outgoing SSN Reset Request, and set asoc->strreset_chunk to NULL CPU0: continue the handler code, hold sk lock, and try to hold asoc->strreset_chunk, crash! In Ying Xu's testing, the call trace is: [ ] BUG: kernel NULL pointer dereference, address: 0000000000000010 [ ] RIP: 0010:sctp_chunk_hold+0xe/0x40 [sctp] [ ] Call Trace: [ ] <IRQ> [ ] sctp_sf_send_reconf+0x2c/0x100 [sctp] [ ] sctp_do_sm+0xa4/0x220 [sctp] [ ] sctp_generate_reconf_event+0xbd/0xe0 [sctp] [ ] call_timer_fn+0x26/0x130 This patch is to fix it by returning from the timer handler if asoc strreset_chunk is already set to NULL. Fixes: 7b9438de ("sctp: add stream reconf timer") Reported-by:
Ying Xu <yinxu@redhat.com> Signed-off-by:
Xin Long <lucien.xin@gmail.com> Acked-by:
Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by:
-
Francesco Ruggeri authored
[ Upstream commit 5b0b9e4c ] In tcp_create_openreq_child we adjust tcp_header_len for md5 using the remote address in newsk. But that address is still 0 in newsk at this point, and it is only set later by the callers (tcp_v[46]_syn_recv_sock). Use the address from the request socket instead. Fixes: cfb6eeb4 ("[TCP]: MD5 Signature Option (RFC2385) support.") Signed-off-by:
Francesco Ruggeri <fruggeri@arista.com> Reviewed-by:
-
Miaoqian Lin authored
[ Upstream commit 084c16ab ] wait_for_completion_timeout() returns unsigned long not int. It returns 0 if timed out, and positive if completed. The check for <= 0 is ambiguous and should be == 0 here indicating timeout which is the only error case. Fixes: 83738d87 ("mtd: sh_flctl: Add DMA capabilty") Signed-off-by:
Miaoqian Lin <linmq006@gmail.com> Signed-off-by:
Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20220412083435.29254-1-linmq006@gmail.com Signed-off-by:
-
Pengcheng Yang authored
[ Upstream commit eba1a872 ] The memory size of ip_vs_conn_tab changed after we use hlist instead of list. Fixes: 731109e7 ("ipvs: use hlist instead of list") Signed-off-by:
Pengcheng Yang <yangpc@wangsu.com> Acked-by:
Julian Anastasov <ja@ssi.bg> Acked-by:
Simon Horman <horms@verge.net.au> Signed-off-by:
-
Adam Ford authored
[ Upstream commit 46ff3df8 ] The pinout of the OMAP35 and DM37 variants of the SOM-LV are the same, but the macros which define the pinmuxing are different between OMAP3530 and DM3730. The pinmuxing was correct for for the DM3730, but wrong for the OMAP3530. Since the boot loader was correctly pin-muxing the pins, this was not obvious. As the bootloader not guaranteed to pinmux all the pins any more, this causes an issue, so the pinmux needs to be moved from a common file to their respective board files. Fixes: f8a2e3ff ("ARM: dts: Add minimal support for LogicPD OMAP35xx SOM-LV devkit") Signed-off-by:
Adam Ford <aford173@gmail.com> Message-Id: <20220303171818.11060-1-aford173@gmail.com> Signed-off-by:
Tony Lindgren <tony@atomide.com> Signed-off-by:
-
