Update Proper pcm ids for compress offload2 usecase.

. Enable incall playback, update proper backend and interface.
. update proper pcm ids for compress offload2 usecase.
. Add incall music uplink config.
. Add incall music downlink config.
. Remove unnecessary usb config.
. Add compress offload playback2 config
. Update mixer controls to support downlink playback with
  compress offload and compress offload2.
. Add mixer control for afe proxy record.

Change-Id: I44c17ded186e86071bf8bc144035ef5b55a51b0c

The mixer will be used for DSDA over PRI_TDM0 and PRI_TDM1.

Change-Id: I5765db7e116bfb2783ceeb2af8fcb0c038488aea

Add tinyalsa support to handle sound card status.
If driver returns error, check and wait for card status online
before triggering close.

Change-Id: I67fd854acca99a78c44daf3c457968c32bc24a3b

SND_MONITOR will be used for SSR support.

Change-Id: I80e0ae53ad1a858b9d4429a8bfe021be0e456890

Remove configs not needed for audiohal.

Change-Id: If4388f44cfdd1767cc17858425082ab7424cd814

update audio start script to ignore modules if already loaded

Change-Id: I35a5a4bf4417af1a341679bd73c123020c70493a

Add missing mixer controls for loopback use cases.

Change-Id: I533f7a82e03e4ee6c0057ae09f8b3c9da2f75b62

add support for bt device

Change-Id: I972ba3bedf51786603b4517002ea06a0ed155543

enable dtmf tone playback over Primary and Secondary mi2s.

Change-Id: Ibf7e5eed7fb4803ff5c453bbc6ba02fcf332e9f5

SA515 uses snd_event to handle SSR co-ordination.

Change-Id: I1a2835531b5ab1b724813bba5e72b215a282d45f

Updating the mixer xml file for DSDA Voice+Voice use case.
This file is used to validate the simultaneous calls on
both subs along with switching of the i2s line.

Change-Id:   I054f00bbaba289049d73cddf7bb10abc36313ebd

Change-Id: Iaa0fad87029d97cb43f3247390289fc0eae9f10e

The driver plays amrwb+ clips in offload mode.

Change-Id: Id198bf69a46f618067d8ecbf1461fb6e9f0a345f

Audio Tuning changes for Record Fluence

Change-Id: I7ec1caa9622c8c784114104772fed1fe8d4210ae

Change-Id: Ic27ce44602ce6502e261f35efcce6446cfa26d1b

Add support for 352.8k and 384k sample rate in capture path.

Change-Id: I0972d3e6e272505c4e5c9e7253e1d89acc5ab309

Add 32bit record and playback support in policy conf file

Change-Id: I060e8f18fef6ce0c94866f0e31f262037baf8570

Added mixer file for SDX AUTO CCARD.

Change-Id: I7573049febe88873043964cfa230612e077b00c5

Update apptype for compress capture path in timestamp mode.

Change-Id: I99c4941124eaeead6c449dff147db3cdc33dd8af

Add new xml files specific for qcs404-rb1 to avoid influence on other
VT based targets.

Change-Id: Icd5b91408d5b0ad00893352dd943a131c88e0f62

Includes following changes:
1. PSPD changes for 4mic + 8ec ref muxed capture matrix coefficients
2. handset quad mic changes to use different dmics

CRs-Fixed: 2625489
Change-Id: I1caa00623208a982f0c9bebcc38ce1be2d4b3d00

route voicemmode2 sub call to secondary mi2s
interface for dsda.

Change-Id: I978c010fa10d173a0648cff5f33e607b9070db85

Add feature flag for record fluence support

Change-Id: I9bd5082697441fafb1aeb416470fe7c680c6f740

when qti-ab-boot feature is enabled, the firmware is mounted by
firmware-mount.service instead of firmware.mount. This fix the issue
that sometimes adsp is OFFLINE after device bootup due to invalid
dependency, see log below:

init_audio.service: Service RestartSec=100ms expired, scheduling restart.
init_audio.service: Failed to schedule restart job: Unit firmware.mount not found.
init_audio.service: Failed with result 'exit-code'.

CRs-Fixed: 2577636
Change-Id: Ie292f53480b7d4dbb85d76fc826619bbec2a89d2

- when out device is line or headphone the far end for
  echo-reference is not being set.
- In mixer path xml file the far end for echo-reference line
  & echo-reference headphones is SLIM0_RX.
- Modify far end to SLIM_RX for echo-reference line
  & echo-reference headphones

Change-Id: I51c52344f59e1332eb3e568e894994590f7fb60b
Signed-off-by: Harendra Gautam <hgautam@codeaurora.org>

install encoders depends on COMBINED_FEATURES qti-audio-encoder.

Change-Id: Id4b8770486dd3b5d499d5f228bba13245064e4fe